首页 > 知识库 > FortiGate > 路由 > 正文

如何过滤或控制重发布路由
2012-12-21 16:53:00 来源：评论：0 点击：

描述:该文档描述如何过滤或控制静态和直连路由重发布至OSPF。该例中，FG80C 和FG300A在area0.0.0.0.互为neighbors需要将FG80C的部分路由重新发布至FG300A:直连网络10.168.6.0/23;静态路由10.11.0.0/24;配置:1.路...

描述:
该文档描述如何过滤或控制静态和直连路由重发布至OSPF。
该例中，FG80C 和FG300A在area0.0.0.0.互为neighbors
需要将FG80C的部分路由重新发布至FG300A:
直连网络10.168.6.0/23;
静态路由10.11.0.0/24;
配置:
1.路由过滤前的配置
FGT80C

config router ospf
        config area
            edit 0.0.0.0
            next
        end
        config network
            edit 1
                set prefix 10.168.0.0 255.255.254.0
            next
        end
        config redistribute "connected"
            set status enable
        end
        config redistribute "static"
            set status enable
        end
    set router-id 0.0.0.114
end

FGT80C# get router info routing-table all

Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP
       O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default

S*      0.0.0.0/0 [10/0] via 172.31.225.254, wan1
S       10.11.0.0/24 [10/0] via 10.168.4.103, vlan4
S       10.12.0.0/24 [10/0] via 10.168.4.103, vlan4
C       10.168.0.0/23 is directly connected, internal
C       10.168.4.0/23 is directly connected, vlan4
C       10.168.6.0/23 is directly connected, wan2
C       172.31.224.0/23 is directly connected, wan1

FG300A

config router ospf
        config area
            edit 0.0.0.0
            next
        end
        config network
            edit 1
                set prefix 10.168.0.0 255.255.254.0
            next
        end
        config redistribute "connected"
        end
        config redistribute "static"
        end
    set router-id 0.0.0.137
end

FG300A# get router info routing-table all

Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP
       O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default

S*      0.0.0.0/0 [10/0] via 192.168.183.254, port5
O E2    10.11.0.0/24 [110/10] via 10.168.1.114, port1, 00:07:25
O E2    10.12.0.0/24 [110/10] via 10.168.1.114, port1, 00:07:25
C       10.168.0.0/23 is directly connected, port1
O E2    10.168.4.0/23 [110/10] via 10.168.1.114, port1, 00:00:38
O E2    10.168.6.0/23 [110/10] via 10.168.1.114, port1, 00:07:33
O E2    172.31.224.0/23 [110/10] via 10.168.1.114, port1, 00:00:38
C       192.168.100.0/24 is directly connected, port2
C       192.168.182.0/23 is directly connected, port5

2.FG80C添加过滤后配置
FGT80C

config router access-list
    edit "OnlyNet6"
            config rule
                edit 1
                    set prefix 10.168.6.0 255.255.254.0
                    set exact-match enable
                next
            end
    next
    edit "1"
    next
    edit "OnlyNet11"
            config rule
                edit 1
                    set prefix 10.11.0.0 255.255.255.0
                    set exact-match enable
                next
            end
    next
end

config router route-map
    edit "Map-OnlyNet6"
            config rule
                edit 1
                    set match-ip-address "OnlyNet6"
                next
            end
    next
    edit "Map-OnlyNet11"
            config rule
                edit 1
                    set match-ip-address "OnlyNet11"
                next
            end
    next
end

config router ospf
        config area
            edit 0.0.0.0
            next
        end
        config network
            edit 1
                set prefix 10.168.0.0 255.255.254.0
            next
        end
        config redistribute "connected"
            set status enable
            set routemap "Map-OnlyNet6"
        end
        config redistribute "static"
            set status enable
            set routemap "Map-OnlyNet11"
        end

    set router-id 0.0.0.114
end

3.检查FG300A上路由表
FG300A2904500072 # get router info routing-table all

Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP
       O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default

S*      0.0.0.0/0 [10/0] via 192.168.183.254, port5
O E2    10.11.0.0/24 [110/10] via 10.168.1.114, port1, 00:01:07
C       10.168.0.0/23 is directly connected, port1
O E2    10.168.6.0/23 [110/10] via 10.168.1.114, port1, 00:01:35
C       192.168.100.0/24 is directly connected, port2
C       192.168.182.0/23 is directly connected, port5

过滤后仅有目标的2条路由被重发布至OSPF

相关热词搜索：

上一篇：如何过滤或控制重发布路由
下一篇：静态路由的管理距离和优先级

分享到：

如何过滤或控制重发布路由
2012-12-21 16:53:00 来源：评论：0 点击：

评论排行

频道总排行

频道本月排行

如何过滤或控制重发布路由 2012-12-21 16:53:00 来源： 评论：0 点击：

延伸阅读：

评论排行

频道总排行

频道本月排行

如何过滤或控制重发布路由
2012-12-21 16:53:00 来源：评论：0 点击：